NOTE: Before upgrading to 3.0.0.7, please see the upgrade process in detail. If you are using a NETGEAR access point managed by wireless controller (WC7520, WC7600 or WC9500), do NOT upgrade to this firmware, as this will revert your managed AP back to standalone mode and the AP would no longer be managed by your wireless controller.
New Features:
- The AP running 3.0.0.7 will support two modes of operation, Standalone mode and BCWM mode (or Business Central Wireless Manager Mode). By default BC mode (or Cloud managed mode) is enabled.
- Supports Configuration, management and monitoring from NETGEAR’s Business Central portal.
- Visit NETGEAR Business Central Page to know all the features supported in this mode.
- Extra Device related Security including encrypted password.
- Default configuration will enable DHCP on Ethernet port, while in previous 2.x versions had DHCP disabled and static IP address of 192.168.0.237 set.
Bug Fixes
- Fixed wireless stability issues.
- Secure password, if admin password is factory default “password”, on first login, software will force to create non-factory-default password.
In case of Business Central managed Mode, password is set at location level rather than on the local AP GUI.
Known issues
- Glitches would be seen by wireless clients when streaming HD multicast video.
- In cloud Mode, AutoRf may not choose the optimum channel. If needed, customer can manually assign channels.
- First time, you upgrade it takes about 8 minutes to encrypt all passwords and boots completely
NOTES:
- The default IP address of the AP is 192.168.0.237
- In the following scenarios AP is expected to reboot automatically for the configuration to take affect:
- Change Country/Region
- After Firmware upgrade
- After Restore Configuration Settings
- Reset factory defaults
-
In all the other conditions AP is not supposed to reboot automatically
- With Rogue AP and more than 2 VAPs (security profiles) enabled, the beacon interval of the AP will be automatically updated for better performance of the Rogue AP algorithm. We recommend not reconfiguring the beacon interval below the suggested value. Anything above the suggested value is fine.
- 1 or 2 VAPs enabled, beacon interval is 100ms
- 3 VAPs enabled, beacon interval is 41ms x 3 = 123ms
- 4 VAPs enabled, beacon interval is 41ms x 4 = 164ms
- 5 VAPs enabled, beacon interval is 41ms x 5 = 205ms
- 6 VAPs enabled, beacon interval is 41ms x 6 = 246ms
- 7 VAPs enabled, beacon interval is 41ms x 7 = 287ms
- 8 VAPs enabled, beacon interval is 41ms x 8 = 328ms
To Install
- Write down all the settings which you changed from the default values, since you may need to reenter them manually.
- Using the Download Link below, download and extract the compressed (zip) file to a convenient place such as your desktop, The firmware filename after extracting is WNDAP350_V3.0.0.7.tar
Download link : http://www.downloads.netgear.com/files/GDC/WNDAP350/WNDAP350-V3.0.0.7.zip
- Login to Web Administration interface of the Access Point -
By default, http://192.168.0.237 is the Administration URL to the Web GUI. Enter admin for the user name and password for the password. - Click Maintenance > Upgrade > Firmware Upgrade.
- Click Browse and select the firmware image you just downloaded.
- Click Upload.
Do NOT interrupt or power off the computer until the upgrade process is completed. Wait for the AP to reboot.
READ THIS BEFORE ATTEMPT TO UPGRADE
Prior to upgrade to v3.0.0.7, the device MUST be running the firmware version indicate in the table below. Upgrading from older firmware version to v3.0.0.7 without the required running firmware version will cause the user not able to access the device Web interface. The only way to recover is by factory resetting the device.
|
Product |
Required running firmware version prior to upgrade to v3.0.0.7 |
|
WNDAP660 |
v2.0.5 |
|
WNDAP360 |
v2.1.12 |
|
WNDAP350 |
v2.1.9 |
|
WNAP320 |
v2.1.6 |
|
WNAP210v2 |
v2.1.5 |
V2.x firmware images for the product can be downloaded from the NETGEAR Global Download Center.
Firmware upgrade from v2.x to v3.0.0.7 will take about 8 minutes. Upgrade from v3.x to v3.x will take about 2 minutes.
Please see table below for upgrade requirement from older v2.x firmware to the latest v2.x firmware.
| Product | Required running firmware version | To upgrade to |
| WNDAP660 | v2.0.4 | v2.0.5 |
| WNDAP360 | v2.1.11 | v2.1.12 |
| WNDAP350 | v2.1.8 | v2.1.9 |
| WNAP320 | v2.1.5 | v2.1.6 |
| WNAP210v2 | v2.1.4 | v2.1.5 |
Once the device is upgraded to v3.0.0.7, it it NOT possible to downgrade the firmware back to v2.x except on WNDAP350.
Method to factory reset the AP via CLI
Using putty/tera term telent/ssh to the AP and run “restore-configuration /etc/default-config” or “restore-factory-default”
This product includes software code developed by third parties, including software code subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL Code and LGPL Code used in this product, are available to you at NETGEAR's Open Source Code Web page