Bug Fixes:
-
,
- When the router static route is private ,it also sends the static route in RIP ,
- Allows to use the bandwidth profile for a schedule based Firewall rule ,
- Fixed Device is vulnerable for POODLE SSLv3 vulnerability (CVE-2014-3566) ,
- Fixed Device is vulnerable for CVE-2014-3568 ,
- SNMP node "nlogSyslogState" should be editable ,
- No DHCP server log and help page missing ,
- nvpnSSLVPNPolicyClientAddressRangeBegin nvpnSSLVPNPolicyClientAddressRangeEnd should not be allowed to set to 0.0.0.0 and 255.255.255.255 ,
- On SSL VPN Client page, Start IP can't be greater than End IP ,
- Cannot enter 0 in last octet of LAN user in LAN-WAN outbound rule ,
- [CLI]Client routes added from SSL_VPN Wizard are not reflecting in both GUI and CLI ,
- Unable to access GUI after adding static route with private enabled ,
- [CLI]Unable to add schedule based firewall rules from CLI ,
- Real QoS values aren't same as online help ,
- IPSec VPN to client: VPN cannot establish when "Remote IP" select "Range" ,
- Not able to add 4th rule in QoS rate control. ,
- Start port cannot be equal to finish port when define a service
Known Issues and limitations:
-
,
- Not able to establish IPV6 SSL-VPN tunnel from java based browsers with java 8 update 20 version. ,
- Unable to run the FTP traffic from FileZilla client over SSL Port forwading tunnel in the windows7 64 bit host ,
- Unable to establish port forwarding tunnel from windows7 64 bit IE9 browser. ,
- Internet Traffic Statistics are not getting updated correctly in auto rollover mode ,
- NFS service support: Only support NFS v4 "mount" command, do not support NFS v2, v3 and "showmount" command ,
- No NAT translation of SIP headers during REGISTER, outbound call and SDP ,
- Observed inconstistant behaviour with voice traffic when server is lying in LAN and DMZ side ,
- Unable to establish the fourth call from LAN side. ,
- Unable to establish the IPV6 manual tunnel with traffic selector as ANY/ANY ,
- Able to Configure IPV6 Address pools and DMZ adverisements prefixes through CLI when DMZ is not enabled ,
- [CLI]Firewalllogs6 table is not updating properly for enabling and disabling logs through cli ,
- Able to run Port triggering inbound traffic with the open port from any WAN hosts ,
- Daylight saving functionality is not working for time zone "GMT-0" ,
- PPPoE over IPv6 WANs are getting restarted and IPv4 WAN is not responding after changing WAN mode for multiple times ,
- Able to establish VPN gw-gw tunnel with mismatch user-FQDN and able to run traffic ,
- Traffic is not following WAN upload or down load(higher one of them )speeds if the upload and down load speeds having large difference ,
- Unable to establish L2TP connection from WAN secondary addresses fail ,
- [IPv6]Unable to run the ftp ,http,iperf traffic on pppoe over ipv6 with DHCP option as "Disable-DHCPv6" ,
- Able to select same wan for both primary and secondary wans for auto rollover WAN mode in ipv4/ipv6 dual stack mode ,
- Unable to get the IP to LAN host after rebooting the device continuously for over night ,
- [IPv6]Displaying the message as address not found instead of 'Blocked from this Browser' for IPv6 policy 'Deny Login From Defined Browsers'
Note: support 5 VoIP phone calls. Next release we will support 50 VoIP phone calls
Installation Instructions:
- Using the Download Link below, download and extract the new firmware to a convenient place such as your desktop. The filename after extracting is srx5308_v4.3.2-7.img
Download Link: http://www.downloads.netgear.com/files/GDC/SRX5308/SRX5308_V4.3.2-7.zip
Note: Reboot the firewall before begining the update process.
- Select Administration > Settings Backup and Firmware Upgrade from the main/submenu.
- In the Router Upgrade section, click Browse.
- Locate the downloaded file and click Upload.
This will start the software upgrade to your VPN firewall. This may take some time. Do not interrupt the upgrade process.
At the conclusion of the upgrade, your firewall will reboot.
Last Updated:10/17/2025
|
Article ID: 26827